ACMME 2017 : (5th Asia Conference on Mechanical and Materials Engineering)

Intro -- 5th Asia Conference on Mechanical and Materials Engineering -- Preface, Conference Committees -- Table of Contents -- Chapter 1: Properties and Processing Technologies of Metals and Alloys -- Spheroidize Annealing and Mechanical Property Evaluation of AISI 1040 Steel -- Microstructures and Tensile Characteristics on Direct Recycled Aluminium Chips AA6061/Al Powder by Hot Pressing Method -- Abrasive Wear on Heat-Treated Recycling Aluminium AA6061 of Various Reinforcement Materials through Powder Metallurgical Process -- Flexural Performance of the Heat-Treated Boron Alloyed Steel -- Process Optimization on Hardness of Precipitation Hardened Al6061 Alloy Using Design of Experiments -- Microstructure and Properties of Ni-Based Alloy Coating with Ultrasonic Frequency Inductive Cladding on Substrate of Cast Irons -- Microstructure and Mechanical Properties of Equiatomic CrMnCoNiCu High Entropy Alloy -- Susceptibility of Acicular Ferrite and Upper Bainite Microstructures to Hydrogen Assisted Cold Cracking Propagation -- Effect of Variable Pitch on Cutting Temperature, Cutting Forces and Surface Roughness Using Nitico30 Cutting Tool when End Milling of Stainless Steel 316L -- Research on Relationship between Cutting Conditions and Chip Formation during End Milling of Aluminium Alloy 6061 -- Effect of Surface Roughness and Oxidation Conditions on Wettability of Borosilicate Glass Sealant -- Technology of Electrochemical Micromachining Based on Surface Modification by Fiber Laser on Stainless Steel -- Experimental Study on the Relationship of Discharge Parameters with Crack Arrest Effects in Inconel 625 Alloy by Electropulsing Treatment -- The Effect of Cutting Speed and Feed Rate on Surface Roughness and Tool Wear when Machining Machining D2 Steel -- Chapter 2: Mechanical Properties of Composites and Intermetallic Compounds Effect of Homogenizing and Age Hardening on Mechanical Property Enhancement of TIG Welded Al6061 SiCp Composites -- Characteristics on Treated Kenaf Fiber Reinforced Polypropylene Composites -- Wear Behavior of In Situ Mg2Si Particle-Dispersed Magnesium Alloys -- Investigation of Friction Coefficient for Twaron-Reinforced Brake Shoe Materials -- A Study of the Structural and Mechanical Characterization of Hybrid Nanocomposite Material -- Fabrication of Al-Based Composites Cylinder Reinforced with In Situ Si/Mg2Si Particles and the Research of its Bench Test -- Crushing Response of Green Square Honeycomb Structure from Sugar Palm & PLA -- Bending Behavior and Electrical Conductivity of Cu/Ni/Al/Ni/Cu Clad Composite -- Fracture Analysis for Attaching Fiber Reinforced Composite on V-Notch Wedge Structure -- Chapter 3: Polymers -- Effect of Calcium Ion Crosslinked Alginate Based Coating on Flame Retardancy of Polyester-Cotton Fabric -- Fabrication of Micro Fluidic Channels in Polymers by Melt-Electrospinning -- Preparation of Porous Polymer Membrane with Controllable Pore Size via Spray Spinning -- Electrospun PVDF-HFP/BR Rubber Composites for High Performance Solid State Electrolytes -- Chapter 4: Biomaterials -- Adhesion of Candida to Vanillin-Coated PMMA Resin -- In Vitro Inhibitory Effect of Vanillin on Candida Biofilm -- Physical Properties of Irreversible Hydrocolloid Impression Material Incorporated with Silver-Nanoparticles -- Antimicrobial Properties of Ag Nanoparticle-Incorporated Irreversible Hydrocolloid Impression Material -- Evaluation of Mechanical Properties of PEEK HAp Bio-Composite Used in Load Bearing Bone Implants -- Surface Modification Effects on Microstructure and Mechanical Properties of Bio-Titanium Alloys -- Chapter 5: Advanced Functional Materials Influence of Modified Carbon Fiber on Properties of Paper Based Friction Materials -- Preparation of Copper-Doped Nickel Oxide Thin Films by Sol-Gel Method Using Nickel and Copper Acetate -- Development of an Optimal Heat Treatment Regime for a Gradient Material Containing Tungsten Carbide -- Investigation of the Influences of Reaction Temperature and Time on the Chemical Reduction of Graphene Oxide by Conventional Method Using Vitamin C as a Reducing Agent -- Performance Comparison of Phase Change Materials for Thermal Energy Storage -- Carbon Nanotube-Poly(Vinylidene Fluoride) Composite Films for Strain-Sensing Applications -- Synthesis and Characterization of TiO2/CNT Nanocomposites for Azo Dye Degradation -- Exhaust Emission Reduction from Compression Ignition Engine by Using Palm Biodiesel Blended with Nano Zinc Oxide Additive -- Synthesis of Hydrophobic Viscose Rayon Fiber Using Nanorod Silica and Chitosan as Surface Modifier -- Chapter 6: Building Materials -- Analysis and Application of New-Type High Performance Cold-Patch Mixture for Pavement -- Research on the Performance of Polymer Modified Cement Matrix Grouting Material Mixed with Polyvinyl Alcohol Fiber -- The Effect of High Temperature Exposure on Properties of Hybrid Fiber Reinforced UHPC -- Properties of Foamed Lightweight Material Produced Using Blended Cement-Limestone Powder -- Properties of Modified Lime-Based Plasters for Renewal of Historical Buildings Exposed to Accelerated Carbonation Test -- Chapter 7: Computational Modeling and Special Experimental Methods -- An ISODATA Approach to the Estimation of Atomistic Definition for Continuum Stress -- Evaluation of Tri-Axial Magnetostriction in Cube-Oriented Fe-Ga Single Crystal by Using X-Ray Diffraction Method -- Multi-Phase Microstructures for Materials with Extreme Bulk Modulus or Thermal Conductivity Continuum-Micromechanical Modeling of Microcapsules-Based Composites -- Keyword Index -- Author Index